个人工具

UbuntuHelp:WifiDocs/Scan for Wireless Network

来自Ubuntu中文

Wikibot讨论 | 贡献2009年11月17日 (二) 21:15的版本

(差异) ←上一版本 | 最后版本 (差异) | 下一版本→ (差异)
跳转至: 导航, 搜索

Scan for wifi Network

Introduction

Scan for and Connect to a Wireless Network from the | Command Line There are a multitude of fine, graphical wireless network configuration programs available to the Ubuntu community. However, there may come a day when you need to acquire a wireless connection from an unknown network on a strange network card from the recovery console. Or perhaps you just want to know how to connect to your home network from the command line. Either way, this HOWTO is for you. This guide assumes that the drivers for your network card are properly set up. Otherwise, it would be too complicated to cover all vendors and chipsets.

Find Network Interface Card

Figure out the name of the interface for your wireless card The interface name of cards for different vendors may be different, which is why this step is needed:

ls /sys/class/net

This will list the interface names for all NICs on your computer. It will probably include eth0 (hardwired NIC), lo (loopback interface for the localhost), and something for your wireless card (like wifi0, or wlan0). For these steps let's call whatever name you find for your wireless NIC [wifi interface]. If you have multiple wireless cards, all of them will be listed. To be sure that the interface that you select is a wireless interface, you can check that its directory contains a "wireless" folder:

cd /sys/class/net/[wifi interface]/wireless/

Release network connections

Just to be sure it's not being used, bring your interface down, release your DHCP connection and then put it back up:

sudo ifconfig [wifi interface] down
sudo dhclient -r [wifi interface]
sudo ifconfig [wifi interface] up

Many of these commands require superuser priviledges (i.e. root access), so the sudo command precedes them. Of course, you could always use "sudo -s" or some other method to login to a shell as the root account, but why complicate matters?

Scan

Scan for open networks

sudo iwlist [wifi interface] scan

Note: In tests this command only worked with Atheros cards. This should return results that look something like this:

wlan0 Scan completed :
Cell 01 - Address: 00:04:E2:D0:D1:96
ESSID:"SMC"
Mode:Master
Channel:6
Frequency:2.437 GHz
Quality=78/100 Signal level=-56 dBm Noise level=-127 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:tsf=00000039cdb32ac3

The ESSID, Frequency and Address are the most important labels here (quality may also factor into your decision, too... higher is better).

Setup Network Interface Card

Set the wireless NIC so that it will connect to the found wireless network:

sudo iwconfig [wifi interface] ap [whatever you found for the MAC address]
sudo iwconfig [wifi interface] essid [whatever you found for essid]
sudo iwconfig [wifi interface] freq [whatever you found for frequency]G

Note the "G" after the frequency, to denote "GHz".

Acuire Network Address

Acquire a DHCP address from your wireless router:

sudo dhclient [wifi interface]

Okay... assuming that your DHCP address was acquired properly, you should have a internet connection all set up. Now, this is probably too complicated of a process to do by hand, but there are a number of ways to automate it. That's outside the scope of this tutorial!

Compatable Chipsets

It has become apparent that not all wireless interface cards work with the scan command. Can you add your results to the table below. Command to find the manufacture and model of your pci card is:

lspci
Type Manufacture Model Pass Fail
pci RaLink RT2561/RT61 x
pci Atheros AR5212/AR5213 x

Authors

mbsullivan - Ubuntu Forums