“UbuntuHelp:WifiDocs/LinksysWPC54G”的版本间的差异
来自Ubuntu中文
小 （新页面: {{From|https://help.ubuntu.com/community/WifiDocs/LinksysWPC54G}} {{Languages|UbuntuHelp:WifiDocs/LinksysWPC54G}} '''This How To explains the setup of Linksys cards that require the ndisw...） |
小 |
||
| 第2行： | 第2行： | ||
{{Languages|UbuntuHelp:WifiDocs/LinksysWPC54G}} | {{Languages|UbuntuHelp:WifiDocs/LinksysWPC54G}} | ||
'''This How To explains the setup of Linksys cards that require the ndiswrapper module.''' | '''This How To explains the setup of Linksys cards that require the ndiswrapper module.''' | ||
| − | |||
Follow these steps: | Follow these steps: | ||
| − | + | # Link to ndis page Ndiswrapper | |
| − | + | ||
| − | + | ||
These instructions for Debian have been helpful for several people configuring linksys cards Arthur's homepage: [http://ch.tudelft.nl/~arthur/wpc54g/ using WPC54G with Debian] | These instructions for Debian have been helpful for several people configuring linksys cards Arthur's homepage: [http://ch.tudelft.nl/~arthur/wpc54g/ using WPC54G with Debian] | ||
| − | + | 2. The Linksys WPC11 ver 4 is a confirmed success. | |
| − | + | 3. In one case at least, manually entering nameserver information into /etc/resolv.conf was required. | |
| − | + | ||
Here is a step-by-step instruction, which workes very well on IBM Thinkpad with WPC54GS (BMC Chipset) card: | Here is a step-by-step instruction, which workes very well on IBM Thinkpad with WPC54GS (BMC Chipset) card: | ||
First, download [http://www.linksys.com/servlet/Satellite?childpagename=US%2FLayout&packedargs=c%3DL_Product_C2%26cid%3D1115416827032&pagename=Linksys%2FCommon%2FVisitorWrapper the unfree drivers]. Unzip the drivers somewhere in your home-directory. | First, download [http://www.linksys.com/servlet/Satellite?childpagename=US%2FLayout&packedargs=c%3DL_Product_C2%26cid%3D1115416827032&pagename=Linksys%2FCommon%2FVisitorWrapper the unfree drivers]. Unzip the drivers somewhere in your home-directory. | ||
| 第24行： | 第20行： | ||
</nowiki></pre> | </nowiki></pre> | ||
Depending on the driver package used, bcmwl5.inf and bcmwl5.sys can be on different places in the subdirectories... | Depending on the driver package used, bcmwl5.inf and bcmwl5.sys can be on different places in the subdirectories... | ||
| − | |||
should show the following: | should show the following: | ||
<pre><nowiki> | <pre><nowiki> | ||
| 第37行： | 第32行： | ||
</nowiki></pre> | </nowiki></pre> | ||
Of course you use your ESSID and WEP-KEY then ;-) | Of course you use your ESSID and WEP-KEY then ;-) | ||
| − | |||
As next, you take up the interface: | As next, you take up the interface: | ||
<pre><nowiki> | <pre><nowiki> | ||
| 第44行： | 第38行： | ||
ifup eth1 | ifup eth1 | ||
</nowiki></pre> | </nowiki></pre> | ||
| − | |||
Wait until dhcp gets it's stuff and then test it (browse google) | Wait until dhcp gets it's stuff and then test it (browse google) | ||
| − | |||
| − | |||
| − | |||
[[category:CategoryDocumentation]] [[category:CategoryCleanup]] [[category:CategoryHardware]] | [[category:CategoryDocumentation]] [[category:CategoryCleanup]] [[category:CategoryHardware]] | ||
[[category:UbuntuHelp]] | [[category:UbuntuHelp]] | ||
2007年11月30日 (五) 22:24的版本
 |
点击翻译: |
English |
请不要直接编辑翻译本页，本页将定期与来源同步。 |
This How To explains the setup of Linksys cards that require the ndiswrapper module. Follow these steps:
- Link to ndis page Ndiswrapper
These instructions for Debian have been helpful for several people configuring linksys cards Arthur's homepage: using WPC54G with Debian 2. The Linksys WPC11 ver 4 is a confirmed success. 3. In one case at least, manually entering nameserver information into /etc/resolv.conf was required. Here is a step-by-step instruction, which workes very well on IBM Thinkpad with WPC54GS (BMC Chipset) card: First, download the unfree drivers. Unzip the drivers somewhere in your home-directory. Then install bcm43xx-fwcutter and use it to get the firmware stuff needed for ndiswrapper:
apt-get install bcm43xx-fwcutter ndiswrapper-utils-1.8 ndiswrapper-common cd ~/windows_drivers/ bcm43xx-fwcutter bcmwl5.sys cp bcm43xx* /lib/firmware modprobe ndiswrapper ndiswrapper -i bcmwl5.inf ndiswrapper -l
Depending on the driver package used, bcmwl5.inf and bcmwl5.sys can be on different places in the subdirectories... should show the following:
bcmwl5 driver installed, hardware present
Then edit /etc/network/interfaces to contain the following. Alternatively you can just use the gnome or kde configuration tools:
auto eth1 iface eth1 inet dhcp wireless-essid linksysgabba wireless-key 0A0A0A0A0A0A0A0A0A0A0A
Of course you use your ESSID and WEP-KEY then ;-) As next, you take up the interface:
ifdown eth0 ifdown eth1 ifup eth1
Wait until dhcp gets it's stuff and then test it (browse google)
