UbuntuHelp:DialupModemHowto/Smartlink

文章出处:

https://help.ubuntu.com/community/DialupModemHowto/Smartlink

点击翻译:

English

Modems supported by the Smartlink driver

Note: Every time you update the Linux kernel, you're going to have to run through the "Compiling the driver" procedure below again. This is usually the case when you upgrade from one version of Ubuntu (e.g. 5.10 Breezy Badger) to another (e.g. 6.04 Dapper Drake).

Preliminaries

These are steps you will only have to run through the first time you build this driver, we're just making sure you have all the installed packages you need. Make sure you have followed the sections of this document entitled If compiling from source and Installing GCC 3.4.

Additionally, you will need the packages sl-modem-source sl-modem-daemon, which, unfortunately, may not be present on the CD and may have to be obtained from another machine.

Compiling the driver

Now you can use module-assistant to compile and install the driver:

 1. $ sudo module-assistant auto-install sl-modem
 1. $ sudo depmod -a (this updates the list of available modules)

Getting the modem to work

Edit the "SLMODEMD_COUNTRY="-line of the file /etc/default/sl-modem-daemon to include your country. The other lines should be fine as default.

For the last step, run $ sudo modprobe slamr and $ sudo /etc/init.d/sl-modem-daemon restart and the device /dev/modem should appear. You can now go on configuring your dialup connection. (PS: This driver seems rather finicky, a reboot may help.)

When using the dialup network configuration tool, set it to use Tone rather than Pulse dialling (unless you know that your area only supports pulse).  Pulse dialling is very rare nowadays and in tests for Feisty, slmodem was not able to pulse dial reliably.

Note about alternative drivers for some slmodems

Some slmodems (those using the ALSA modem drivers, in this case) do not need compilation. An example is the winmodem of HP Pavilion zv5120us (which uses snd-atiixp-modem as the modem driver). Refer to your scanModem output if this is the case for you. To make such a modem work, see the section above about "Modems supported by ALSA drivers", or notes just below. This note on linmodems.org explains it:

From http://archives.linmodems.org/21040

Slamr has ceased to be the appropriate driver under more current 2.6.n kernels
 If your modem controller is one of these

     PCI  ID       modem controller  name/source     low_level_driver
    ========        =================    =========         ==================
    1002:434d          ATI                            snd-atiixp-modem
    1002:4379          ATI                                 "
    1106:3068          VIA                            snd-via82xx-modem
    10b9:5451          ALI 5451 audio with modem      snd-ali5451-modem
    8086:????           many Intel controllers        snd-intel8x0m
    10de:00d9          Nvidia Corp                          "
    1039:7013          SIS 630                              "
     Others?                                                "

Dapper 6.06 Special Instructions

Due to a BUG in Ubuntu Dapper, you may need to follow these instructions, instead of the above module compilation instructions. First, check whether the bug is fixed yet. If it is, you can do the above steps. Steps below were taken from here.

1. Read this entire document, as the steps below only compliment it and you should have all the preliminaries done as described for the Smartlink modem, but you can omit installing gcc-3.4 as this is not required for Dapper. Basically the sl-modem driver has to be installed first and then the sl-modem-daemon. The daemon in the repositories will work after an installation, but the /dev/ttySL0 will not be rewritten and the symlink to /dev/modem will not exist after a reboot. The new daemon found in the debian repos solve this. There was a mention that the daemon now looks for ungrab-winmodem and if you get an error message refering to this, you may need to install as well.

2. Download sl-modem-daemon2.9.9d+e-pre2-5.deb and sl-modem_2.9.9d+e-pre2.orig.tar.gz from the debian website http://packages.debian.org/unstable/misc/sl-modem-daemon. I have found that the slmodem-2.9.11-20051101.tar.gz works better in dapper and this can also be downloaded from the linmodem website http://phep2.technion.ac.il/linmodems/packages/smartlink/.

3. It may also be required that you download and install the ungrab-winmodem from the linmodem website as well.

4. Copy the sl-modem-daemon file to your local repository and update your Packages.gz file, this will allow you to install with Synaptic etc. Or use your favourite way to install a .deb file.

5. Copy the sl-modem_2.9.9+e-pre2.orig.tar.gz ( or preferably the slmodem-2.9.11-20051101.tar.gz) file to your Desktop and right click on it and select “Extract here” and a folder wth the same name will be created with the extracted files on your desktop.

6. Now rename the folder to an easier name such as “slmodem”

7. Open a terminal and cd in to the slmodem folder

8. Type make

9. Type sudo make install

10. Type sudo modprobe slamr

11. Type dmesg | grep slamr

12. Now install sl-modem-daemon2.9.9d+e-pre2-5.deb with Synaptic or in your own favourite way.

13. Use Kppp to query the modem, if this works you are there!

14. Edit /etc/default/sl-modem-daemon to change the line SLMODEMD_COUNTRY= USA to i.e SOUTHAFRICA or your country

15. Type sudo /etc/init.d/sl-modem-daemon restart to restart the daemon.

16. If you do a “Query modem” in Kppp and you will see that your country has changed.

17. It seems as if the Smartlink modems with Netodragon chip MDV92XP does not work, but the ND92XPA chip works.

Back to the main wiki