“UbuntuHelp:IPMI”的版本间的差异
来自Ubuntu中文
小 |
小 |
||
第7行: | 第7行: | ||
<pre><nowiki> | <pre><nowiki> | ||
a) BIOS POST: | a) BIOS POST: | ||
− | (i) Enable "Console Redirection" in BIOS Setup. For example, COM2 / | + | (i) Enable "Console Redirection" in BIOS Setup. For example, COM2 / |
− | 19.2Kbps / 8N1 | + | 19.2Kbps / 8N1 |
− | (ii) Disable "Enable Console Redirection after POST" in BIOS setup. | + | (ii) Disable "Enable Console Redirection after POST" in BIOS setup. |
</nowiki></pre> | </nowiki></pre> | ||
I recommend these settings in your /boot/grub/menu.lst | I recommend these settings in your /boot/grub/menu.lst | ||
<pre><nowiki> | <pre><nowiki> | ||
serial --unit=1 --speed=19200 --word=8 --parity=no --stop=1 | serial --unit=1 --speed=19200 --word=8 --parity=no --stop=1 | ||
+ | |||
#This additional line was also suggested also, but I only found its behavior annoying. | #This additional line was also suggested also, but I only found its behavior annoying. | ||
terminal --timeout=5 serial console | terminal --timeout=5 serial console | ||
+ | |||
# defoptions=console=tty0 serial console=ttyS1,19200n8 | # defoptions=console=tty0 serial console=ttyS1,19200n8 | ||
+ | |||
# altoptions=(recovery mode) single console=tty0 serial console=ttyS1,19200n8 | # altoptions=(recovery mode) single console=tty0 serial console=ttyS1,19200n8 | ||
+ | |||
# xenkopt=console=tty0 serial console=ttyS1,19200n8 | # xenkopt=console=tty0 serial console=ttyS1,19200n8 | ||
+ | |||
</nowiki></pre> | </nowiki></pre> | ||
Be sure to run sudo update-grub | Be sure to run sudo update-grub |
2007年12月6日 (四) 10:39的版本
点击翻译: |
English |
请不要直接编辑翻译本页,本页将定期与来源同步。 |
This page is about setting up IPMI on ubuntu.
- apt-get install ipmitool
- /usr/share/ipmitool/ipmi.init.basic
- less /usr/share/doc/ipmitool/README.gz
a) BIOS POST: (i) Enable "Console Redirection" in BIOS Setup. For example, COM2 / 19.2Kbps / 8N1 (ii) Disable "Enable Console Redirection after POST" in BIOS setup.
I recommend these settings in your /boot/grub/menu.lst
serial --unit=1 --speed=19200 --word=8 --parity=no --stop=1 #This additional line was also suggested also, but I only found its behavior annoying. terminal --timeout=5 serial console # defoptions=console=tty0 serial console=ttyS1,19200n8 # altoptions=(recovery mode) single console=tty0 serial console=ttyS1,19200n8 # xenkopt=console=tty0 serial console=ttyS1,19200n8
Be sure to run sudo update-grub Next, go into your /etc/event.d/ directory. Create a ttyS0 file from one of the other tty files. Change this line: exec /sbin/getty 19200 ttyS0 Do the same thing for ttyS1 Last, edit /etc/securetty and add ttyS1
Links
http://wiki.adamsweet.org/doku.php?id=ipmi_on_linux http://www.ecst.csuchico.edu/~dranch/LINUX/IPMI/ipmi-on-linux.html - Howto Supermicro