UbuntuHelp:HardwareSupportComponentsWirelessNetworkCardsLinksys
出自Ubuntu中文
 |
点击翻译: |
English
|
请不要直接编辑翻译本页，本页将定期与来源同步。
|
Parent: Wifi Wireless Cards Supported | Discuss this page
[编辑] Summary
[编辑] PCI
[编辑] WMP54G
| Version | Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| (Ver 1.0/2.0/3.0) | Broadcom BCM4306 | bcm43xx/b43 | No | No | No | Works with bcm43xx (may be flaky), but not b43 (Bug #182716). Also works with ndiswrapper. (all this for Ver 03) | 2008-08-09
|
| (Ver 4.0) | Ralink RT2500 | rt2500pci | ? | Yes | Yes | Detected in Network Settings as ra0 and started working after WAP details were input | 2005-10-17
|
| (Ver 4.1) | Ralink RT61 | rt61pci | ? | Yes | No | For Hardy see Bug#200142. Works only in Feisty if you put to "blacklist" the "rt61pci" module BEFORE install the card. If not, your computer will freeze often. There is an other module: "rt61" it works fine, with WEP too. | 2008-07-09
|
| (Ver 4.5) | BCM4318 [AirForce One 54g] | bcm43xx-fwcutter | ? | Yes | No | Work good in Feisty and Gutsy. Does not work in Hardy. There are some threads around about how to make it work in Hardy, but it is hit-or-miss. | 2008-05-17
|
[编辑] WMP55AG
| Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| Atheros | madwifi | ? | Yes | Yes | Detected in Network Settings as ath0 and started working after WPA was configured | 2007-02-05
|
[编辑] PCMCIA
[编辑] WPC 11
| Version | Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| (Ver.2.5) | ? | orinoco_cs | No | Yes | No | run "cardctl ident" and add info to /etc/pcmcia/config under wireless network adapters section. Be sure to include manfid and bind to orinoco_cs. Then just reboot and run "gksudo network-admin" in console and configure eth0...works like a champ! |
|
| (Ver.3) | Prism/Intersil | ? | Yes | Yes | Yes | Detected in Network Settings as eth0 and started working after WAP details were input | 2005-08-15
|
| (Ver.4) | Realtek RTL8180L | rtl8180 | ? | Yes | Yes | Tested on Ubuntu 7.10 kernel version 2.6.22-14-generic. Card was detected and needed only to be set up in network-manager. "Link" light non-operable, but link established at 11 Mb/s. | 2007-10-14
|
| (Ver.4) | Realtek | ? | ? | Yes | Yes | Working fine. No work needed.(Xubuntu Edgy) | 2006-12-04
|
| (Ver.4) | Realtek | rtl8180 | ? | Yes | No | Needed the ndiswrapper (documentation)|and the Realtek driver (download) to get it working in Feisty. | 2008-01-12
|
[编辑] WPC54AG
| Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| AR5212 802.11abg NIC (rev 01) | madwifi | ? | Yes | No | Ran apt-get update and card was found. Using WPA-PSK with distro's madwifi drivers connecting to Dlink di-624 version 3. | 2006-09-19
|
[编辑] WPC54G
| Version | Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| (ver 1.2) | Broadcom (BCM4306 rev3) | ? | ? | Yes (after fix) | No | Get recognized in the setup process, but unable to use it. After setup completes, the card is shown in the network interfaces (as eth0, all hardware details are shown too), but the system is unable to activate it. Updating the firmwares (link broken) fixes the problem. To do this when Ubuntu starts, open the restricted drivers management and enable bcm43xx. | 2006-03-14
|
| (Ver.2) | Texas Instruments ACX111 | acx | No | Yes | Yes | Card works out of the box since Feisty, but does not work with WPA. For older Versions, or to enable WPA support, use NDISwrapper according to this howto: Ndiswrapper | 2008-04-02
|
| (Ver 3 | Broadcom | no (ndiswrapper) | ? | No | No | Couldn't get any of the windows drivers from linksys.com to work (they don't have a version 3 one listed right now) but I tried the driver off the installation CD with ndiswrapper and it worked like a charm! Just follow normal ndiswraper driver installation with the NT driver from the linksys install CD that comes with the card (built in driver works flawlessly with the 2.6.15 kernel, ndiswrapper not needed. Do not know if it will work for install.) In Feisty installing Broadcom firmware here will get v.3 cards working. | 2006-07-05
|
| (Ver 3.2?) | Broadcom (BCM43??) | ? | ? | Yes | Yes (with Gutsy - just install drivers) | Hardware recognized immediately upon re-start/start-up. Clicking through warnings re: closed-source/proprietary hardware should bring you options to download firmware updates. Following downloads and install, you should be up and running (note: you may also need to manually configure the network - enter SSID, WEP, DHCP setup or not, etc.) | 2008-05-18
|
| (Ver.4) | ? | no (ndiswrapper)) | ? | No | No | This card type is very tricky to get working, must have drivers for the SPECIFIC version of the card. | 2005-12-27
|
| (Ver 7.1) | Atheros | madwifi | ? | ? | Yes | It just works (Dapper Drake 6.06). | 28-09-2006
|
[编辑] WPC54GS-UK with Speedboost
See WifiDocs/Device/LinksysWPC54GS-UK
| Version | Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| Broadcom (BCM4318) | ? | ? | Yes | No | See here.|Card works well once the Broadcom firmware is installed WifiDocs/Driver/bcm43xx. | 2006-11-07
|
[编辑] USB
[编辑] WPC54GS with Speedboost
| Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| Broadcom (BCM4306 rev3) | no (ndiswrapper) | ? | No | No | Card works well with windows driver (from CD) & ndiswrapper - the instructions here were simple and effective. The instructions also worked for my Belkin F5D7010 card (rev3, listed above) without alteration. | 2006-03-16
|
[编辑] WUSB11
See WifiDocs/Device/LinksysWUSB11 and WifiDocs/Device/Linksys_WUSB11v4_(ndiswrapper)
| Version | Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| (Ver.2.8) | ? | ? | Yes | Yes | Just choose wireless network in networking, and works. Xubuntu 6.06. | | 2009-07-15
|
[编辑] WUSB11B
| Version | Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| (Ver.2) | ? | Unknown/Likely | Yes | Yes | No command-line needed, works perfect the first try. Tested on Dapper Beta 2 | | 2006-05-09
|
[编辑] WUSB300N
| Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| ? | winxp driver | ? | ? | No | Used ndiswrapper 1.9 to install driver then had to use ndisgtk's "Configure Network" button to manually select the wireless network's SSID, change encryption to WEP (although, in fact there is no security set on the router) and set DHCP - seemed to only work with these particular attributes set. Downside of ndiswrapper is no network feedback/info from the Network Manager notification area icon on signal strength, etc. | 6-May-2008
|
[编辑] WUSB54G
[编辑] WUSB54GC
See WifiDocs/Device/LinksysWUSB54GC
| Chipset | Driver | Supports network install? | Supported in installed system? | Works "out of the box" | Comments | Last Updated
|
| RAlink RT2571W/RT2671 | No | Yes | Yes | Works out of box with Gutsy and Hardy. If not, see WifiDocs/Device/LinksysWUSB54GC | | 2008-06-01
|
| rt73usb | rt73 | ? | Yes? | Yes | Works out of the box with Feisty 7.04, Gusty 7.10, Hardy 8.04 | 20-08-2008
|
[编辑] WUSB54GP
See WifiDocs/Device/LinksysWUSB54GP
[编辑] WUSB54GS
[编辑] v.1 & v.2
See WifiDocs/Device/Linksys_WUSB54GS_v1___v2
[编辑] v. 4
See WifiDocs/Device/Linksys_WUSB54Gv4
[编辑] WMP54GX
See WifiDocs/Device/Linksys_WMP54GX
See also http://jelnet.free.fr/jlnt_indx.htm (under "Matériel") for an excellent overview of different revisions/chipsets for some Linksys "products" (just marketing names really).
